Search Results

Standard

Brake Drum Qualification Recommended Practice

2022-12-20

CURRENT

J2686_202212

This SAE Recommended Practice is intended for qualification testing for brake drums used on highway commercial vehicles with air brakes using an inertia-dynamometer procedure. This document consists of two distinct tests: Part A, durability and speed maintenance test, and Part B, heat check drag sequence test. Each test can be considered to be an independent evaluation of the brake drum which tests different properties.

Standard

Vehicle Electronic Programming Stations (VEPS) System Specification for Win32®

2022-11-22

HISTORICAL

J2461_202211

SAE J2461 specifies the recommended practices of a Vehicle Electronics Programming Stations (VEPS) architecture.in a Win32® environment. This system specification, SAE J2461, was a revision of the requirements for Vehicle Electronics Programming Stations (VEPS) set forth in SAE J2214, Vehicle Electronics Programming Stations (VEPS) System Specification for Programming Components at OEM Assembly Plants (Cancelled Jun 2004). The J2214 standard has been cancelled indicating that it is no longer needed or relevant.

Standard

Contaminants for Testing Air Brake Components and Auxiliary Pneumatic Devices - Truck and Bus

2022-11-22

CURRENT

J2024_202211

This SAE Information Report establishes a minimum level of uniform recipes for contaminants which may be used when durability testing pneumatic components to obtain additional information on how a device may perform under more true-to-life operating conditions. This type of contamination testing, however, is not meant to replace the type of performance testing described in SAE J1409 and SAE J1410. Durability testing in the presence of contamination will yield results more reflective of actual in-service field conditions and provide an additional evaluation of pneumatic devices. While the contaminant supply rate and other test criteria of the device being tested must be set by the device manufacturer or user, the items covered in this document will be:

Standard

Crane Hoist Line Speed and Power Test Procedure

2022-10-26

WIP

J820

This document applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if the load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed. This recommended practice applies to all mechanical, hydraulic, and electric powered hoist mechanisms.

Standard

Brake Force Distribution Field Test Procedure for Truck and Bus

2022-10-07

CURRENT

J225_202210

This SAE Recommended Practice provides a field test procedure and instructions for air braked single unit trucks, buses, and combination vehicles. Brake force distribution field testing with systems post-reduce stopping distance changes is still appropriate, however, vehicles with electronically controlled braking systems are not covered in this document and may need to be addressed in the future. It also provides recommendations for: a Instrumentation and equipment. b Vehicle preparation. c Test of air-braked single and combination vehicles. d Calculation of brake force distribution. e This test procedure is intended to be used as a field procedure. If a more refined method, utilizing laboratory equipment, is required, refer to SAE J1505.

Standard

Disposable Hydraulic Filter Element - 190 L/min Flow, 21 MPa Collapse Pressure, Filtration Ratio = 75 at 7 μm

2022-09-14

WIP

J2321/2

This specification sheet establishes requirements for a high collapse pressure configuration filter element of a specific configuration with a minimum filtration ratio of 75 for particles larger than 7 µm when designed and tested in accordance with SAE J2321 and this specification sheet.

Standard

Minimum Performance Criteria for Falling Object Guards for Excavators

2022-09-08

CURRENT

J1356_202209

This SAE Recommended Practice applies only to excavators, as defined in ISO 6165, working above ground, near an excavated or free-standing bank or mine face which is higher than the top of the cab, or in demolition applications of freestanding buildings or objects higher than the top of the cab.

Standard

Mobile Crane Working Area Definitions

2022-09-01

CURRENT

J1028_202209

This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting, clamshell, dragline, magnet, pile driver, or similar service.

Standard

Horn - Forward Warning - Electric - Performance, Test, and Application

2022-08-05

CURRENT

J1105_202208

The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated, operator controlled forward warning horn devices, primarily intended for use on self-propelled, work machines as defined by SAE J1116 (limited to categories of (1) construction and (2) general purpose industrial).

Standard

Brake Force Distribution Performance Guide - Truck and Bus

2022-07-26

CURRENT

J1854_202207

This SAE Recommended Practice establishes performance guidelines for the threshold pressure and brake force output of the brakes on the axles of air-braked towing trucks, truck-tractors, truck-trailers, and converter dollies with GVWRs over 4536 kg (10000 pounds) designed to be used on the highway in combination with other air-braked vehicles of this type in commercial operations.

Standard

Self-Propelled Sweepers Sweep-Ability Performance

2022-07-26

CURRENT

J1702_202207

This SAE Standard establishes a method of disclosing the sweep-ability performance of self-propelled sweepers that use broom means for sweeping and collection, together with either a mechanical- or pneumatic-conveyance system for the transfer of “sweepings” into a collection hopper.

Standard

Air Filter Element Test Method

2022-07-14

CURRENT

J1533_202207

This SAE test method establishes a uniform test procedure for determining the gravimetric (mass based) efficiency and pressure drop performance levels of operator enclosure panel type filters on off-road, self-propelled work machines used in earth moving, and forestry, as defined in SAE J1116 and for agricultural equipment as defined in ANSI/ASAE S390, and equipped with an operator enclosure with a powered fresh air system. ISO/TS 11155-1 may additionally be used, which describes the use of particle sizing devices to measure the fractional (particle size) efficiency of panel type filters for automotive cabin filter applications. Automotive cabin filters are similar to filters described in this procedure, and the ISO/TS 11155-1 test method is therefore directly applicable.

Standard

Brake Adjustment Limit for Air Brake Actuators

2022-07-13

CURRENT

J2899_202207

This SAE Recommended Practice applies to S-CAM, wedge, and disc air brake actuators where the stroke can be measured without disassembly from the brake.

Standard

Motorcycle Turn Signal Lamps

2022-06-27

WIP

J131

This SAE Standard provides test procedures, requirements, and guidelines for motorcycle turn signal lamps. It does not apply to mopeds.

Standard

Primary Single Phase Nominal 120 VAC Wiring Distribution Assembly Design—Truck and Bus

2022-06-22

CURRENT

J2698_202206

This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.

Standard

Occupant Restraint and Equipment Mounting Integrity - Rear Impact Ambulance Patient Compartment

2022-06-21

CURRENT

J3044_202206

This SAE Recommended Practice describes the test procedures for conducting rear impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mount testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.

Standard

Ambulance Litter Integrity, Retention, and Patient Restraint

2022-06-21

CURRENT

J3027_202206

This SAE Recommended Practice describes the testing procedures required to evaluate the integrity of a ground ambulance-based patient litter, litter retention system, and patient restraint when exposed to a frontal, side or rear impact. Its purpose is to provide litter manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent ensures the patient litter, litter retention system, and patient restraint utilizes a similar dynamic performance test methodology to that which is applied to other vehicle seating and occupant restraint systems. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.

Standard

Engine-Off Cab Heating and Air Conditioning Systems Test Procedure and Performance Requirements - Trucks with and without Sleepers

2022-06-20

CURRENT

J2918_202206

This SAE Recommended Practice establishes uniform test procedures and performance requirements for engine-off heating, ventilation, and air conditioning (HVAC) systems in order to achieve driver thermal comfort in both winter and summer rest periods. This specification will apply to heavy trucks with and without sleeper compartments, including but is not limited to Class 6, 7, and 8 powered vehicles.

Standard

Cab Air-Conditioning Test Procedure - Heavy Trucks with and without Sleepers

2022-06-20

CURRENT

J2646_202206

This SAE Recommended Practice establishes a uniform test procedures for on highway trucks equipped with an air-conditioning system used to condition the air in the cabin and sleeper compartment of the vehicle. This specification will apply to heavy trucks with and without sleeper compartments.

Standard

Occupant Restraint and Equipment Mounting Integrity – Side Impact Ambulance Patient Compartment

2022-06-20

CURRENT

J2956_202206

This SAE Recommended Practice describes the test procedures for conducting side impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.